Your Location:Home > Products center > Cement Making Machine > Bucket Elevator

Bucket Elevator


Hoisting Height: 28-32.7m

Conveying Capacity: 3-60m³/h

Range of application: Coal, cement, stone, sand, clay and ore.

Introduction

Bucket elevator is the device which is used to vertically lift the limestone, coal, gypsum, clinker, dry clay that have been crushed and other granular material, raw material, cement, braize and other powdered materials.

Bucket Elevator

Using the hopper to scoop up the materials from the storage, the materials are raised to the top with the conveyor belt or chain, the materials flip down after bypassing the top wheel and the bucket hoist pour the materials into the receiving slot. The driving belt of the bucket elevator with driving force generally uses a rubber belt, which is attached to the lower or above driving drum. As for the plate chain bucket elevator, it is generally equipped with two parallel transmission chains, a pair of drive sprocket and a pair of redirecting sprocket. Bucket elevators are generally equipped with a chassis to prevent the dust from flying upward.

Features

1. Lower power consumption and driving power. Adopting the intensive layout of inflowing feeding, induced discharge and large capacity hopper.

2. High lifting height, good transmission capacity, fully sealed of the body and small environmental pollution.

3. Having no strict requirements on the types and characteristics of the materials, which can not only lift the general powdery and granular materials, but also hoist the abrasive materials.

4. Operational reliability, advanced design principles and processing methods ensure the reliability of the whole machine operation.

Matters Needing Attention

1. When the bucket elevator is working, to make sure that the feeding should be even and the discharge pipe should be smooth to avoid causing blockage. If the clogging happened, the operator should immediately stop feeding and shut down the machine to handle the blockage. The operator can not directly put the hand into the base.

2. During the normal operation, the hopper belt should be in the middle of the cylinder. If the phenomenon of deviation or the belt is loose is found, they should be adjusted by the tensioning device to avoid the collision friction between the hopper and cylinder.

3. Strictly prevent the large piece of foreign matter from entering the base to avoid to damage the hopper, affecting the normal work of the bucket elevator.

Parameter

Technical parameters of ring chainbucket elevator

Specification Max.lifting height
(m)
Conveying capacity
(m³/h)
Max.size
(mm)
Pitch of buckets
(mm)

Motor prower

(kw)

TH160 25 7-12 15-20 400 3-4
TH200 28 8-15 20-30 500 3-5.5
TH250 30 10-25 25-35 500 4-7.5
TH300 30 25-35 30-40 500 5.5-11
TH315 40 30-40 35-45 512 5.5-15
TH400 40 45-60 40-55 512 11-22
TH500 40 65-80 50-60 512 15-30
TH630 40 100-120 60-65 688 18.5-37
TH800 40 130-150 65-75 920 22-45

Technical parameters of wire belt bucket elevator

Specification Max.lifting height
(m)
Conveying capacity
(m³/h)
Max.size
(mm)

Bucket Volume

(L)

Motor prower

(kw)

TDG160 80 34 0-20 2.6 2.2-11
TDG200 80 45 0-25 4.1 3-15
TDG250 80 71 0-30 6.5 5.5-22
TDG315 80 101 0-35 10 7.5-30
TDG400 80 158 0-40 16 15-45
TDG500 80 218 0-45 25 18.5-55
TDG630 80 345 0-50 40 30-90
TDG800 80 491 0-50 61 45-132

Plate chain bucket elevator

Specification

Max.lifting height

(m)

Max.lifting capacity

(m³/h)

 Percentageallowed

(%)

Pitch

(mm)

Motor power

(kw)

10 25 50 75 100
Max.size(mm)
NE15 40 16 65 50 40 30 25 101.66 1.5-4
NE30 59 31 90 75 58 47 40 152.4 2.2-7.5
NE50 62 60 90 75 58 47 40 152.4 3-15
NE100 58 110 130 105 80 65 55 200 7.5-30
NE150 65 170 130 105 80 65 55 200 11-37
NE200 73 220 170 135 100 85 70 250 18.5-75
NE300 61 320 170 135 100 85 70 250 22-75
NE400 47 420 205 165 125 105 90 300 45-90
NE500 58 500 240 190 145 120 100 300 45-132

Send us a Inquiry

If you have a question about our products, we'd like to hear from you.Rest assured we won't share your name, address or phone number with anyone. We're passionate about our company and want to help any way we can. Thanks for taking the time to get in touch with us.

Product: *Name:
Phone: *Email:
Message: